Newsletter

FAQ'S

Are they difficult to fit?

All Superpro  bushes can be fitted with normal workshop tools and equipment. Where necessary, grease is supplied for effective operation and to assist fitment, but in many cases the most difficult job will be removing the old bush!

What is the life expectancy of Superpro  Polyurethane Bushes?

As Superpro ’s polyurethane material is not affected by petrochemicals, water, salt, daylight and is extremely resistant to abrasion, with normal use Superpro  bushes will last up to six times longer than original rubber components. The material also remembers its shape - long after a rubber bush will have ‘set’ in a distorted position.

Do Superpro  Polyurethane Bushes come with a warranty?

Yes 3 years or 36,000 miles (60,000km)

Will I improve my handling by fitting Superpro  polyurethane suspension bushes?

Yes, by fitting Superpro  bushes you will experience consistent steering geometry, and enhanced handling and control of any vehicle as it does not deteriorate as rubber will. Due to Superpro 's unique polyurethane material and design features, stricter tolerances can be used which will give you improved performance characteristics such as; better road holding, increased tyre life, more responsive steering, and longer service life of suspension components.

Do you recommend using grease with Superpro  bushes?

In all the locations on a vehicle where bushes have a pivoting action, it is essential that grease is used. Due to the characteristics of polyurethane, and the way in which the bushes behave, they start to act as bearings instead of just a gap filler, and as little friction in movement as possible is vital to avoid uncomfortable increases in noise vibration and harshness (NVH). All Superpro  kits include grease where necessary; of course we do not include grease where it is not necessary for the performance of the component to do so.

Does the colour of your bushes indicate how hard the ride will be when fitted?

No. Superpro  bushes are supplied in one standard colour: blue. Superpro  believes that it is important to supply a bush that is designed to achieve the optimum performance for its location on the car – without creating a harsh or uncomfortable ride. This means that a car may need bushes of three or four different materials to deliver the best improvement in suspension performance without creating excessive levels of NVH. Colour coding by material hardness would result in either specifying multi-coloured car kits of varying hardness of materials, or kits of one colour and hardness which would compromise performance.

Should I fit Superpro  Polyurethane Bushes for motorsport applications?

Yes - including off road and track competition use. As Superpro  bushes offer improved handling performance over rubber, they are ideal for use in racing, rallying and other forms of motorsport. They are especially beneficial when a competition car is also used on the road and where nylon bushes or solid joints are not appropriate.

How many of each Superpro  bush kit do I need per location?

Generally only one. Superpro  bush kits are assembled to include all the components needed to replace the bushes on both sides of the car in the same location. The exception to this is if the same bush kit is used on the front and rear of the vehicle, if both the front and rear bushes are required two bush kits will need to be purchased in this situation.

I use my car daily, will fitting Superpro  make the ride uncomfortable?

No. Due to the unique properties of the raw material and the design techniques used to manufacture Superpro  Polyurethane Bushes they will not cause any extra noise, vibration or harshness (NVH) over the standard rubber bushes. This makes them suitable for road cars and race cars alike.

Are your bushes a copy of the originals?

No. Due to the different way polyurethane works. This requires the design of the bush to be different than the original rubber bush. This can give Superpro  bushes a major advantage over the standard rubber versions as they can eliminate problems where the rubber bushes are prone to premature failure.

My car has been lowered; can I still fit Superpro  bushes?

Yes. Lowering a car actually puts more stress on the original bushes and will make them deteriorate faster. By fitting a lowering kit on your car and keeping the original bushes you will not get the best from it as the suspensions arms will still be able to move making the cars geometry unstable. Fitting Superpro  to the car help keep all the suspension arms in the correct position – even under heavy cornering. Superpro  also offers the option of caster & camber adjustment bushes which can help compensate for geometry changes as a result of lowering.

My car pulls to one side, can you help?

Yes. Superpro  has a range of caster and camber adjusting bush kits for various models. These can be used when the cars original geometry settings have gone beyond the factory adjustments.

Is it cheaper to buy a complete set of bushes for my car?

Yes. Superpro  has many applications where the individual bush kits can be purchased separately or as a complete kit – these kits are cheaper to buy than the individual bush kits together. If there are no kits listed for your application please contact us and we will try to accommodate your needs.

Are Superpro  Polyurethane Bushes available for classic cars?

Yes, we have an extensive range of bushes available for classic cars.

If you do not have my car listed in your catalogue, could you still help me?

We may be able to match your requirements from our existing range of over 3000 part numbers. It may also be possible to modify an existing bush or we could supply you with a polyurethane billet for you to machine yourself. We also have an on-going program of range development and expansion.

Do Superpro  make anything else in polyurethane other than suspension bushes?

We may be able to match your requirements from our existing range of over 3000 part numbers. It may also be possible to modify an existing bush or we could supply you with a polyurethane billet for you to machine yourself. Have an on-going program of range development and expansion.

What is resilience?

Resilience is the speed at which an elastomer will return to its original shape after being deformed.